seal assembly
英 [siːl əˈsembli]
美 [siːl əˈsembli]
网络 永久封隔器的密封总成; 密封总成; 密封装配
双语例句
- Prepare valve-stem seal, protective cap and assembly driver.
准备气门杆密封件、保护帽和装配冲棒。 - Likewised, should the mechanical shaft seal assembly require replacement, the gear set dose not have to be removed from the pump.
同样地，机械密封轴部件取代，不需要从泵体上移除。 - Remove stopper used to seal the converter assembly opening.
拆下用于密封变矩器总成开口的止动块。 - Mechanical seal repair process more complicated, after assembly to ensure no leakage of the mechanical seal, mechanical seal technology essential check size.
机械密封检修工艺较为复杂，要保证组装后的机械密封无漏泄，机械密封技术尺寸的校核必不可少。 - Mechanical seal pumps in accordance with the assembly of the above three steps can be achieved after the assembly of mechanical seal without leakage and other problems.
水泵的机械密封按照以上三个步骤进行组装，可以实现组装后的机械密封无漏泄及其它问题的出现。 - Improvement of Actuator Piston Seal Assembly for Water Turbine Driven Generator
水轮发电机组接力器活塞密封的改进 - Should avoid making it subjected to lateral force, lateral force caused by untight seal assembly.
应避免使其受到侧向力，侧向力过大会造成密封不严。 - The structure consists of four parts: shell, whole seal assembly, hanger assembly, self seal rubber core assembly.
其结构由壳体、全封总成、悬挂器总成、自封胶芯总成四部分构成。 - New polished rod seal assembly and its application
新型光杆密封盒及其使用 - Seal assembly of three stages ( guide sleeve, shiftable seal ring unit and disc-seal) is adopted to accomplish the sealing of oil heat extraction equipment.
采用3级（导套、浮动密封环组、盘根）组合密封结构设计方法，实现石油热采密封系统的密封要求。 - The damage type of early failure of mechanical seal was introduced for the high pressure carbomate pump, through making the analysis and calculation from aspects of seal washing water filter accuracy, seal washing water quantity, seal assembly and oil seal failure etc.
介绍了高压甲铵泵机械密封早期失效的损坏形式，通过对密封冲洗水过滤器精度、密封冲洗水量、密封装配、油封故障等方面的分析和计算，论证了机封失效的原因； - This paper presents experimental results for shaft seal assembly with three kinds of different support seats.
本文介绍了三组不同支座的轴密封部件试验结果。 - The leakage reasons of molten plastics for hot runner mold are discussed in detail, the methods of preventing leakage are introduced from operation processing, seal design of hot runner system and assembly process of hot runner plate.
详细讨论了热流道模具熔体泄漏的主要原因，从操作工艺、热流道系统密封设计和热流道板装配工艺等3个方面介绍了防止熔体泄漏的措施。 - In this paper, the performance of floating end face seal in high speed rock bit is investigated with FEM. The assembly process, structure displacement and stress variation of contact area under different working condition are calculated and simulated.
运用有限元法对高速牙轮钻头浮动端面密封的性能进行分析，计算模拟了浮动端面密封在装配过程和不同工作条件下结构的变形和接触表面应力变化。 - It is not only concerned with the study of physical theory about temperature, pressure and liquid movement law, but also concerned with structure design technology of seal ring assembly, which creates a problem on mutual conjunction between theory and technology.
密封问题既涉及到物理理论的研究，如温度、压力、流体运动规律等，也涉及到密封装置的结构设计技术。它是理论与技术相互关联的问题。 - New full floating seal assembly for intermediate rod on reciprocating pump
一种新型全浮动往复泵介杆密封装置 - This article gives a brief description of a special tool for assembling and disassembling of seal rings in the wedge-shaped gate valve for oil ( gas) well-head assembly.
本文简要地介绍了装拆采油（气）井口楔形闸密封圈的一种专用工具。 - A polished rod seal assembly with new structure is introduced.
介绍了一种新型结构的光杆密封盒。 - It is proved that the shaft end seal and the seal oil protection system after being reconstructed met the application demand and ensured the normal running of the compressor assembly-bringing with it outstanding economic and social efficiency.
改造后的轴封结构和密封油保护系统，经实际运行，完全符合使用要求，收效明显，保证了机组长周期运行。 - Mechanical Seal Failure Analysis and Assembly
机械密封失效的原因分析及装配 - Design of New Type of Die Casting Mould with Tightwire and Idler Wheel for Angle Core Pulling The Air Pressure Seal Equipment of the Bearings in the Idler Pulley Assembly of the WEDM
新型钢丝绳滚轮斜抽芯压铸模设计线切割机上下导轮轴承气压密封装置 - Seal and Assembly Process for Hot Runner mold
热流道注射模的密封与装配工艺 - The causes of leakage in piping system, which includes pipes, flange seal faces and valves, were discussed. Major preventive measures taken against the leakage of piping system in piping design, construction and assembly are introduced.
探讨了管道系统中管道、法兰密封面及阀门泄漏的原因，以及在配管设计和施工安装过程中避免泄漏的一些主要措施。 - Plate seal assembly with heavy swinging hammer in the sinter machine
烧结机用重锤摆动板式密封装置